JV-N
COMPACT FLAT
POWER RELAY FOR
HEATER LOADS
JV-N RELAYS
FEATURES
• High 16 A capacity
About Cd-free contacts
16
.630
22
.866
The contacts are high capacity 16A,
125 V AC.
• Compact, flat type with low 10.9 mm
.429 inch height
We have introduced Cadmium free type
products to reduce Environmental
Hazardous Substances.
(The suffix “F” should be added to the
part number)
Please replace parts containing
Cadmium with Cadmium-free products
and evaluate them with your actual
application before use because the life of
a relay depends on the contact material
and load.
10.9
.429
Compact flat type with low surface area
of 16 × 22 mm .630 × .866 inch and
height of 10.9 mm .429 inch.
• High sensitivity at 200 mW
High sensitivity at 200 mW coil power
consumption.
• Represses contact terminal heat
The contact terminals are larger and
thicker compared to the existing JV relay.
This limits the rise in temperature of the
terminals when there is a large current
flowing to approx. 28°C 62°F (normal
current of 16 A).
• Conforms to the various safety
standards
UL/CSA, TÜV approved.
Compliance with RoHS Directive
SPECIFICATIONS
Contact
Characteristics
Arrangement
1 Form A
Max. operating speed
20 cpm
Initial contact resistance, max.
(By voltage drop 6 V DC 1 A)
Max. 12 ms (DC 4.5 V to 48 V)
Max. 100 mΩ
AgSnO2 type
Operate time*1 (at nominal voltage)
Max. 8 ms (DC 100 V)
Contact material
Release time*2 (at nominal voltage)
Initial insulation resistance
Max. 5 ms
Nominal switching
capacity
16 A 125 V AC, 10 A 277 V AC
10 A 30 V DC, 10 A 125 V AC
Min. 1,000 MΩ (at 500 V DC)
Between open
contacts
Initial breakdown
voltage
1,000 Vrms for 1 min.
2,500 Vrms for 1 min.
4,500 V
Max. switching power
Max. switching voltage
Max. switching current
2,770 VA, 300 W
277 V AC, 30 V DC
Rating
(resistive
load)
(Detection
current: 10 mA
Between contacts
and coil
16 A (AC 125 V), 10 A (DC)
Surge voltage between contact and
coil
Min. switching capacity#1
(Reference value)
100 mA, 5 V DC
Max. 45°C (DC 4.5 V to 48 V) *3
Max. 55°C (DC 100 V)*4
Expected life (min. ope.)
Mechanical (at 180 cpm)
Temperature rise
2×107
Ambient temperature
–40 to 70°C –40 to 158°F
(DC 4.5 to 48 V)
16 A 125 V AC
10 A 30 V DC
3×104
105
Sealed
type
Electrical
at resistive
load
Flux-resistant type
10 A 125 V AC
–40 to 60°C –40 to 140°F
105
Conditions in case of operation,
transport and storage*8
(at 20 cpm)
(DC 100V)
Humidity: 5 to 85 % R.H.
(Note freezing and condensing
at low temperature)
Coil
200 mW (DC 4.5 to 48 V)
600 mW (DC 100 V)
Nominal operating power
Air pressure: 86 to 106 kPa
Functional
Shock resistance
200 m/s2{20G}*5
1,000 m/s2{100G}*6
10 to 55 Hz *7
at double amplitude of 1.6 mm
#1 This value can change due to the switching frequency, environmental conditions,
and desired reliability level, therefore it is recommended to check this with the
actual load.
Destructive
Remarks
Functional
Vibration
* Specifications will vary with foreign standards certification ratings.
*1 Excluding contact bounce time
resistance
10 to 55 Hz at double
amplitude of 2 mm
Destructive
*2 Excluding contact bounce time, without diode
*3 By resistive method; nominal voltage applied to the coil; contact carrying current:
16A, at 70°C 158°F
Unit weight
Approx. 8g .28 oz
*4 Nominal voltage applied to the coil, at 60°C 140°F
*5 Half-wave pulse of sine wave: 11 ms; detection time: 10 µs
*6 Half-wave pulse of sine wave: 6 ms
*7 Detection time: 10 µs
*8 Refer to 6. Conditions for operation, transport and storage mentioned in
AMBIENT ENVIRONMENT.
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
